Suche
Anzeige der Dokumente 11-20 von 48
Aufsatz
Excellent superelasticity in a Co-Ni-Ga high-temperature shape memory alloy processed by directed energy deposition
(2020-04-30)
A Co-Ni-Ga high-temperature shape memory alloy has been additively manufactured by directed energy deposition. Due to the highly anisotropic microstructure, i.e. columnar grains featuring a strong near-⟨001⟩ texture in build direction, the as-built material is characterized by a very low degree of constraints and, thus, shows excellent superelasticity without conducting a post-process heat treatment. As characterized by in situ deformation testing and post-mortem microstructural analysis, additive manufacturing ...
Dissertation
The Fatigue and Corrosion Fatigue Behavior of Austenitic Stainless Steel AISI 304 after Deep Rolling at Various Temperatures
(2019-09)
The austenitic stainless steel AISI 304 was deep rolled at 20 °C (RTDR), -195 °C (CTDR), and 550 °C (HTDR). The deep rolling pressures used for each deep rolling temperature were 1.0, 1.7, and 2.4 bar. From microstructural investigation, the largest compressive residual stress field was found in RTDR, and the highest amount of martensitic content and plastic deformation were found in CTDR. The strain aging effect was only found in HTDR.
In the rotating bending fatigue tests, the strain aging effect after HTDR is ...
Aufsatz
On data-driven nonlinear uncertainty modeling: Methods and application for control-oriented surface condition prediction in hard turning
(2020-10-16)
In this article, two data-driven modeling approaches are investigated, which allow an explicit modeling of uncertainty. For this purpose, parametric Takagi-Sugeno multi-models with bounded-error parameter estimation and nonparametric Gaussian process regression are applied and compared. These models can for instance be used for robust model-based control design. As an application, the prediction of residual stresses during hard turning depending on the machining parameters and the initial hardness is considered.
Aufsatz
Experimental Analysis of Residual Stresses in CFRPs through Hole-Drilling Method: The Role of Stacking Sequence, Thickness, and Defects
(2023-05-09)
Carbon fiber reinforced plastics (CFRPs) gained high interest in industrial applications because of their excellent strength and low specific weight. The stacking sequence of the unidirectional plies forming a CFRP laminate, and their thicknesses, primarily determine the mechanical performance. However, during manufacturing, defects, e.g., pores and residual stresses, are induced, both affecting the mechanical properties. The objective of the present work is to accurately measure residual stresses in CFRPs as well ...
Aufsatz
Cyclic Crack Growth in Chemically Tailored Isotropic Austenitic Steel Processed by Electron Beam Powder Bed Fusion
(2021-11-01)
The present study analyzes the cyclic crack propagation behavior in an austenitic steel processed by electron beam powder bed fusion (PBF-EB). The threshold value of crack growth as well as the crack growth behavior in the Paris regime were studied. In contrast to other austenitic steels, the building direction during PBF-EB did not affect the crack propagation rate, i.e., the crack growth rates perpendicular and parallel to the building direction were similar due to the isotropic microstructure characterized by ...
Aufsatz
Damage Tolerance Evaluation of E-PBF-Manufactured Inconel 718 Strut Geometries by Advanced Characterization Techniques
(2020-01-06)
By means of electron beam powder bed fusion (E-PBF), highly complex lightweight structures can be manufactured within short process times. Due to the increasing complexity of producible components and the entangled interplay of damage mechanisms, common bulk material properties such as ultimate tensile or fatigue strength are not sufficient to guarantee safe and reliable use in demanding applications. Within this work, the damage tolerance of E-PBF-manufactured Ni-based alloy Inconel 718 (IN 718) strut geometries ...
Aufsatz
Tribological Performance of Additively Manufactured AISI H13 Steel in Different Surface Conditions
(2021-02-16)
Additive manufacturing of metallic tribological components offers unprecedented degrees of freedom, but the surface roughness of most as-printed surfaces impedes the direct applicability of such structures, and postprocessing is necessary. Here, the tribological performance of AISI H13 steel samples was studied. These were additively manufactured through laser powder bed fusion (L-PBF), also referred to as selective laser melting (SLM). Samples were tested in four different surface conditions: as-printed, polished, ...
Aufsatz
Elevated Temperature Mechanical Characteristics and Fracture Behavior of a Novel Beta Titanium Alloy
(2023-02-03)
In the present work, the elevated-temperature deformation characteristics and microstructural evolution of a Ti-5V-5Mo-5Cr-4Al alloy in solution-treatment conditions were studied under a tensile load at temperatures in the range of 25 to 550 °C and strain rates between 0.001 and 0.1 s-¹. The results obtained indicated that, essentially, dynamic recovery (DRV) was the dominant softening mechanism in the case of the regimes considered. An analysis based on transmission electron microscopy (TEM) and the assessment of ...
Aufsatz
Overmoulding of Additively Manufactured Titanium Inserts Using Polyoxymethylene (POM)—Evaluation of Bond Quality as a Function of Process Parameters
(2021-06-15)
Due to their process-induced porous surfaces, additively manufactured structures are not optimized for applications in which friction is a key factor. To improve the frictional properties of additively manufactured titanium inserts of various thicknesses, two tribologically optimized POM materials, which differ in terms of filler composition and contents, were used to overmould the inserts. The titanium inserts were manufactured in two different building directions, resulting in a variation in surface roughness. The ...
Aufsatz
Microstructural Constituents and Mechanical Properties of Low-Density Fe-Cr-Ni-Mn-Al-C Stainless Steels
(2022-07-23)
Metallic material concepts associated with the sustainable and efficient use of resources are currently the subject of intensive research. Al addition to steel offers advantages in view of lightweight, durability, and efficient use of high-Fe scrap from the Al industry. In the present work, Al was added to Fe-12Cr-(9,12)Ni-3Mn-0.3C-xAl (x = 0.1–6) (wt.%) stainless steels to assess its influence on microstructure and mechanical properties. According to density measurements based on Archimedes’ principle, densities ...